The House is on a Diet

Remember this crappy old laundry sink from an earlier post? Rusted out legs, leaking faucet, and slow drain? It was junk and needed to go.




It was replaced with this new unit from Menard's. It's about 400 pounds lighter, since it's not reinforced concrete.




The crappy old sink has been taking up space in the basement long enough, and since the dumpster is here, it's time to get rid of it. Out comes Mr. Sledgehammer and the old sink is now reduced to rubble. That trailer was really not liking carrying that much weight. I probably should have hooked it up to the tractor, but I didn't want to screw around with it since it was raining. If there wasn't so much wrong with this sink, I would have found a way to re-use it. Busting it up and hauling the debris up the stairs in buckets wasn't a whole lot of fun. At least it's done...




It's all your's, Nate. Come get it! It'll be in the dumpster next to your shed for a few more days.

Aww, Hell No.

I started removing carpet from my attic this afternoon, since it is in the mid 70's outside and it should be tolerable if I run a box-fan to get the hot air out of the attic. I knew there was some planking in the attic, but with the carpet in place I couldn't get a good idea as to what was there. I removed one large piece of carpet and found that the PO planked a LOT more of the attic than I had expected. Plus, the planks had no spacing between them for me to check the depth of the existing insulation. I'm working on the assumption that the area between the joists under the planking is fully insulated, but I think I'm going to have to pull up a lot of the planks just to make sure. Plus, I need to install some recessed lighting in the kitchen and wouldn't be able to easily run the wiring if I leave the planks in place. I'm not really looking forward to this, but if the attic is cooled off a lot tonight it shouldn't take more than an hour to get most of the planks removed, along with the carpet. I do plan on leaving a small section of planking to get from one end of the house to the other, but since I'm not going to store anything in there other than insulation, the excess has got to go. There is about 4' of clearance between the plans and the peak of the roof. Being 6'3", I'm expecting this little adventure to suck.




By the way, the PO did have a nice way to get into the attic without going through the living area in the house. There is an access hatch in the wall of the garage. I'm not sure how safe it is as far as fire barriers go, but it's handy for getting crap (carpet and padding, for instance) in and out of the attic. There was a pulley attached to the rafters in the garage, so I just attached a small rope and it worked like a charm. Here, I've got a fan running to force as much hot air out as possible before I spend any quality time with the planks and insulation.




Hey Nate, here's your shed. I even left all the original nails in the wood for you. UPS didn't want to come pick it up for you for some reason. So much for "What can Brown do for you?"...

I Love the Smell of Sawdust in the Afternoon. It Smells Like. . . . Victory.

After a week of hauling the old shingles, I'm finally done with that project. The roof still needs a little attention at the gutters and I still need to install the light tube, but the heavy work is done (finally). It still surprises me how much room the old shingles took up in the 20 yard dumpster. It's almost half-filled already! The trailer in the dumpster is what I used to move the shingles from the yard to the dumpster. Every effort was made to keep the debris as far forward and stacked as high as possible so I wouldn't be walking over nails. I also wanted to make sure I didn't waste room since I don't want to rent another dumpster any time soon. With the shingles done, it was time to destroy that crappy old shed.




Nate, these pictures are for you! The wood siding was in decent shape, but there was a lot of rot because the builder of this masterpiece didn't use pressure-treated wood. I started with the sledge hammer and knocked the siding off of two sides. The area with missing framing was heavily rotted and took almost no effort to remove. I was going to cut the shed into pieces, but found it was easier to just dismantle it with the sledge.




Here's why you should use pressure treated wood for the sill plates. The entire corner was rotted away and filled with bugs. It didn't help that the roof leaked heavily. I was surprised with how well the shed was built, but that they went stupid and used a flat roof and a swing-in door. The more I look at it, the more I think this wasn't really a shed, but more of a garden shed for potting plants. Size-wise, this shed would have been useless for lawnmowers or other lawn-care tools.




Did I mention the roof leaked? Black isn't a good color for roof supports. This beam was rotted, as were the ends of the roof decking which were above it.




Here, most of the roof has been taken apart except for the last bit which was above the shed door. The roof was covered with 4' x 4' shingles. Well, they weren't really shingles, but were made from the same material. There were plenty of nails holding the "shingles" in place, but none of them were caulked or covered in tar. The seams (and there were a LOT of seams on this roof) were also not caulked or tarred. Gee, I wonder why it leaked? Bad choice of roof design, no slope to the roof, and poor execution. This might have worked if they had used a one-piece rubber membrane of some type or at least slopped the whole roof with tar.