Two plumbing tips:
1. When the directions say "finger-tight" or "finger-tight plus 1/4 turn" or something very specific like that, they probably say it for a reason.
2. If you're going through all the trouble of replacing a toilet (or sink for that matter) and supply line(s), replace the old shut-off valve at the same time. It's $3.49 for a new 1/4-turn shut-off valve people, spend the freakin' money.
I bring these items up because I didn't bother listening to my own advice, resulting in a toilet replacement which took twice as long as it should have. I decided to replace the last remaining original toilet in the house because I'm sick of wasting water with the old one. I had the new one sitting here waiting for the past three months, but the bathroom remodel is still a month or two away. Might as well get rid of the old crapper while I have the dumpster! I decided to "save time" and re-use the original shut-off valve, even though it sprays water unless it's fully open or fully closed. Well, with the new toilet in it drips water through the packing. Ten minutes later, the water is off, the new valve is on, and the water is back on. That problem is solved. Now it's dripping water at the braided-stainless supply hose where it connects to the valve. Damn, I just tightened it down with a crescent wrench, well beyond the 1/4 turn recommendation. Off it comes so I can check the rubber washer. It looks OK, so I re-install and tighten the recommended way and it's finally done.
For now.
It'll have to come out soon so I can gut that bathroom for the renovation. At this time, I'm planning on moving the toilet location to help open up some room in there, since it's kind of a small bathroom in it's current configuration. We'll see how that goes.....
Showing posts with label check valve. Show all posts
Showing posts with label check valve. Show all posts
Sunday, August 19, 2007
Saturday, April 7, 2007
Freakin' Cold Weather
Overnight in the teens, high temp today should hit 37. Normally, I couldn't care less as I've got plenty of work to keep me busy inside. As I was getting some stuff from the basement, I noticed that the sump pump well was full and ready to turn on to send the water outside. Well, I'm always ready to see my handy-work in action, so I trip the pump and wait. Hmmm.... the water level isn't going down but the pump is running. WTF? A quick trip outside and I find the problem. The water line leaves the house in the middle of the rear of the house. Instead of simply dump the water straight onto my patio, the line hangs a left and goes all the way to the side of the house - approx 20' of pipe. The pipe is laying on the ground and has some dips in the line where water can pool. Well, that pooled water froze and the line is now plugged. Since the dirt has built up so much over the decades, there really isn't any good slope to the yard anymore for this to work as it should.
The problem has just now started thanks to that wonderful check valve I installed. Previously, the water could drain back out of the line from either end. Now, once it's in the line it's in the line and won't go anywhere unless the slope allows gravity to do it. Once it warms up a little this will be added to the project list. I don't want to get rid of the check valve, but I'd also like the pump to be able to work.
The problem has just now started thanks to that wonderful check valve I installed. Previously, the water could drain back out of the line from either end. Now, once it's in the line it's in the line and won't go anywhere unless the slope allows gravity to do it. Once it warms up a little this will be added to the project list. I don't want to get rid of the check valve, but I'd also like the pump to be able to work.
Sunday, April 1, 2007
Basement Updates
In an earlier post I mentioned the old sump pump and cement laundry tub. We've had some wet weather over the past few days which means the sump pump should be seeing some action. Every time I hear it turn on, it reminds me of how old it is and what kind of damage we could get if it died. I used that as the incentive to replace it today. How old is it? No idea, but the rust makes me think it's been here a few years.
A run to Ace and Menards got me all the pieces I thought I would need. Actually, I went overboard as usual and got two different check valves, various clamps, etc to make sure I could do the job in one shot. I go to these stores so often that I'll just return the extra stuff. Luckily this plan worked, as I ended up using various parts from both places to get the pump installed. A check valve was added at the pump housing, and I added a PVC line from there to the old sump output line. Testing of it found no leaks, and everything appears to work as planned. Besides the piece of mind, the pump should need to work much less than the old pump now that the check valve is installed. The only "problem" is that the new pump sits lower in the sump and keeps the cement covers from sitting close around the pump like it used to. Now there's enough room for the cat to get in there and drown. Oh damn, would that make me sad...
I've also started putting together the new laundry tub. My only concern is connecting the new PVC to the old metal line. Actually, it's not the connecting of the pieces which worries me, it's breaking the old parts when I take it apart which has me worried. I'd like to just connect the parts together without having to remove the entire drain line, but we'll see how that goes. Before loosening the pieces, I'll give 'em a soak in penetrating oil to help them come apart. The new plastic pieces will also be put together with an extra layer of plumber's putty in the joints to help avoid leaks. For once, I'd like to have a leak-free setup on the first try!
A run to Ace and Menards got me all the pieces I thought I would need. Actually, I went overboard as usual and got two different check valves, various clamps, etc to make sure I could do the job in one shot. I go to these stores so often that I'll just return the extra stuff. Luckily this plan worked, as I ended up using various parts from both places to get the pump installed. A check valve was added at the pump housing, and I added a PVC line from there to the old sump output line. Testing of it found no leaks, and everything appears to work as planned. Besides the piece of mind, the pump should need to work much less than the old pump now that the check valve is installed. The only "problem" is that the new pump sits lower in the sump and keeps the cement covers from sitting close around the pump like it used to. Now there's enough room for the cat to get in there and drown. Oh damn, would that make me sad...
I've also started putting together the new laundry tub. My only concern is connecting the new PVC to the old metal line. Actually, it's not the connecting of the pieces which worries me, it's breaking the old parts when I take it apart which has me worried. I'd like to just connect the parts together without having to remove the entire drain line, but we'll see how that goes. Before loosening the pieces, I'll give 'em a soak in penetrating oil to help them come apart. The new plastic pieces will also be put together with an extra layer of plumber's putty in the joints to help avoid leaks. For once, I'd like to have a leak-free setup on the first try!
Friday, March 30, 2007
... And up to my eyes (Part 3)
Fake brick around a fake fireplace. What are the odds this masterpiece will survive the renovation? Not good I'll bet. The mantle is actually real stone, but I'll still destroy it all as I take it apart. Even my son wants to take a hammer to it - he makes me proud.
The mechanicals in the basement all work, but some of the pieces are in need of updating. The sump pump is older than me and doesn't have a check-valve in the line so every time it pumps out water, about half of it comes right back into the crock! The water softener needs to be disconnected and cleaned out since the old salt has formed a salt-bridge inside keeping it from working properly. Since we moved in a month ago, we've probably run more water through it than it's seen in over a year. The water heater on the far left of the picture is past it's life expectancy, so I expect to be replacing it soon. Fine with me, as it'll be a good selling feature for the house when we move. When I replace the sump pump, I plan to add a battery backup pump as well. The sump runs enough that it makes me worry what would happen if/when the power goes out for any length of time.
The laundry tub (or what's left of it) works, but the faucet is shot, it's got some large rust spots, and one leg is rusted away. Not too safe considering it probably weighs a few hundred pounds and is made of concrete! I already have a replacement sink, faucet, and drain so it'll be replaced soon.
As our home inspector was going through the place, he couldn't help but laugh at this wiring job. That hard-wired connection goes to the stove. Not what I'd call a "safe" job as you can't unplug the stove. The wire also doesn't have much of a drip line to it, so if anybody spills anything which gets behind the stove, it could drip down the wire and into the rigged junction box. Obviously this was not done by a professional electrician or anybody in possession of a clue. We'll remove this joke and the new stove will be set up for gas.
Back to the main floor, we see some lovely architecture from the 60's. The same detail is found by the front door. Both areas will be torn out and modernized when I start renovating these areas.
The mechanicals in the basement all work, but some of the pieces are in need of updating. The sump pump is older than me and doesn't have a check-valve in the line so every time it pumps out water, about half of it comes right back into the crock! The water softener needs to be disconnected and cleaned out since the old salt has formed a salt-bridge inside keeping it from working properly. Since we moved in a month ago, we've probably run more water through it than it's seen in over a year. The water heater on the far left of the picture is past it's life expectancy, so I expect to be replacing it soon. Fine with me, as it'll be a good selling feature for the house when we move. When I replace the sump pump, I plan to add a battery backup pump as well. The sump runs enough that it makes me worry what would happen if/when the power goes out for any length of time.
The laundry tub (or what's left of it) works, but the faucet is shot, it's got some large rust spots, and one leg is rusted away. Not too safe considering it probably weighs a few hundred pounds and is made of concrete! I already have a replacement sink, faucet, and drain so it'll be replaced soon.
As our home inspector was going through the place, he couldn't help but laugh at this wiring job. That hard-wired connection goes to the stove. Not what I'd call a "safe" job as you can't unplug the stove. The wire also doesn't have much of a drip line to it, so if anybody spills anything which gets behind the stove, it could drip down the wire and into the rigged junction box. Obviously this was not done by a professional electrician or anybody in possession of a clue. We'll remove this joke and the new stove will be set up for gas.
Back to the main floor, we see some lovely architecture from the 60's. The same detail is found by the front door. Both areas will be torn out and modernized when I start renovating these areas.
Subscribe to:
Posts (Atom)
